Search Results for: metering

  • Liquid Metering

    Fuel Oil Metering, whether tariff or consumption, is an important part of any system. Being brand independant and highly experienced, we can advise you on the most suitable metering method and supply you with the best possible solution for your particular situation.

    read more
  • Gas Metering

    Flow meters let you keep a close eye on the precise amount of gas being consumed. Volumetric or mass-flow meters monitor gas volumes for custody transfer (Sm3/Nm3, energy value in megajoules), gas turbine efficiency monitoring and/or quality control. We can measure flows of 1 million Nm3/h and above with accuracies to within 0.1%. Automatic (hourly, daily, weekly) reporting can include pressure, temperature, and energy value per standard cubic meter for billing.

    read more
  • Liquid Filtration & Separation

    All contaminants are removed from the oil stream; basket strainers will remove the coarse debris, and coalescing filters will remove the fine solids & water. The strainers and filters can be installed in a 2×100% configuration, integrated switchover valves allow you to switch to the stand-by filter without interrupting the oil flow.

    read more
  • Loading & Unloading

    Oil loading & unloading systems provide safe, clean and quick means to connect trucks or railway tank cars to the oil transfer system. The systems can be fitted with pumps, anti-spark provisions and tariff metering.

    read more
  • Analyzing

    The analyzer section can report the composition of gas components and calculate or measure the heat value, dew point and other values. These values can all be needed for custody transfer payments of gas turbine burner control. The sample probe guides a small stream of reduced -pressure gas to the analyzer, which cracks the gas into multiple components and vents waste gas to a safe location.

    read more
  • Fuel Oil Conditioning

    Fuel Oil Treatment systems prepare and condition the fuel oil to meet the exact fuel specifications required prior to combustion. Fuel oils are commonly used as a back-up fuel for gas fired power plants or as the main fuel for engine power plants. Our fuel oil treatment systems will be custom engineered for your project and can meet even the most stringent fuel specifications required for gas turbines.

    read more
  • Final Run

    The final run consists of a series of equipment that form the last line of defense to protect the Gas Turbine from foreign material. Its components may include consumption flow metering, performance heating, filtering and a shutoff valve section.

    read more
  • Venting & Flaring

    Our integrated line of pressure and vacuum relief vents, flame/detonation arresters and related vapor control devices are used primarily in process industries.

    read more
  • Buffering

    The buffer consists of a compressor, a buffer volume and an outlet system (usually a heater and pressure reducing system). The goal is to store enough gas to keep the gas turbine running if the gas supply is interrupted. The buffer must provide gas for long enough to allow the turbine control system to perform actions like switching over to backup fuel (usually diesel), start pumps and adjust burner settings. Buffer volume is customized to each project, since each combination of gas pressure, consumption and composition requires a different volume.

    read more
  • Pressure Reducing

    This section reduces the gas pressure to a stable level suitable for gas turbines, with the actual pressure being determined by self acting regulator valves. Remote set-point adjustment can fine tune the output pressure for each individual run, or force run switching for even wear on parts. Pressure reducing components vary depending on pressure levels, pressure differences, and allowable pressure drop across the system for low inlet pressures.

    read more
  • Heating

    The gas temperature drops significantly when pressure is reduced for gas turbine consumption. This Joule-Thomson-effect is countered by heating up the gas prior to pressure let-down, and prevents liquid dropout from the gas if one of the components passes below its dew point. strategically located sensors and switches monitor the design temperature, water level and pressure, safeguarding the entire system. Any additional results of a risk assessment/hazard and operability study (Hazop) can be implemented in the control philosophy for each project section.

    read more
  • Pressure Boosting

    Where needed due to low inlet pressures from the gas supplier, pressure boosting compressors increase the pressure to gas turbine levels and can be installed in parallel with the heating and pressure-reduction sections. The pressure booster is integrated in our control narratives in close cooperation with well-known compressor suppliers and uses proven technology.

    read more
  • Control System

    The control system consists of  elements like Programmable Logic Controller, Input/Output cards, barrier computers, flow computers, relays, motor soft starters and UPS. These can be housed in a special conditioned container, with dimensions varying according to customer specifications. Operators miss nothing with precise control across the full range of operating pressures and temperatures. When they need it, there’s remote assistance and diagnostics across the web. The control panel can be operated locally, or remotely from another site. Petrogas can supply data communications to the control room.

    read more
  • Condensate Storage

    The condensate storage section holds drained material from the filter separator (and/or Knock-out drum) until it can be hauled from site. As elsewhere in our system, we use proven and reliable technology and can customize the design to your exact requirements. The vessel can have an unlimited range of volumes, depending on your specific needs. Options include single-wall tank or double wall for additional containment safety, a vacuum leak detector, condensate unloading pump, various level measurements, and a flame arrestor for maximum safety.

    read more
  • Fuel Gas Conditioning

    Gas systems must work safely and efficiently at all times, so we build quality and reliability into our skid-mounted conditioning stations right from the start. Every one of our turnkey systems is factory-tested: we QC everything, from the actuators on the inlet valves to the filter cartridges in the final filters. That’s why many of the world’s leading Engineering, Procurement & Construction (EPC) contractors and end users turn to Petrogas for peace of mind. We have supplied gas treatment systems to some of the world’s largest combined cycle power plants, natural gas distributors, and processing and industrial plants.

    read more